One of the most significant health hazards in the welding process is the generation of fumes and gasses. Do you weld on galvanized metals? Zinc is the coating used on galvanized metals, and when you heat the metal, it produces vaporized metal droplets which are called fumes. This is the smoky haze which consists of fine particles of metals or silicates. When you breathe these fumes, they may work deeply into your lungs.
The typical effect of breathing zinc fumes is metal fume fever. One or two hours or more after welding-without proper personal protection-you may experience severe thirst, pain in the legs, shivering, congestion in the head, dryness and tickling of the throat, and a cough. In very bad cases, you may feel severe shivering, a high fever, buzzing in the ears, nausea, vomiting, and even hallucinations and convulsions. Your symptoms will usually last 24 hours.
Some of you may weld for a period of time and find some of the symptoms appeared, then went away. You may actually have built up an immunity that hides the full effects. If you take a break from welding over the weekend or over a holiday, the symptoms will often come back again the next time you weld on galvanized metal. Because of this behavior, metal fume fever is sometimes known as "Monday morning sickness."
Protect yourself, if you weld on galvanized metals, by following these precautions:
- In all operations where metal fumes are present, you should work in a well ventilated area. The best way to protect yourself against metal fumes is to use local exhaust ventilation at the source of the smoke. Do not re-circulate the air in the shop.
- If good local ventilation is not possible you should wear an approved respirator, which will fit underneath your welding helmet, to protect yourself from fumes. This respirator collects the fume particles and keeps them from entering your lungs. (A paper dust mask is not adequate).
- If you find white dust inside your welding shield, you are not properly protecting yourself from the fumes.
- After you have finished welding, wash your hands and face thoroughly with soap and water.
- Do not eat, drink, or smoke in areas contaminated by welding fumes.
- If you think you are experiencing symptoms of metal fume fever, report it to your supervisor. Physicians familiar with this illness say that the best treatment is to drink plenty of water and go to bed and rest.
Finally, did you know that you can "contaminate" your family by bringing home zinc particles on your clothing? Protect both yourself and your family-weld safely.
Friday, September 14, 2007
WHAT YOU NEED TO KNOW ABOUT WELDING & CUTTING
Protecting yourself when performing welding operations depends on your understanding of the hazards involved and the proper way to control them. Control of welding hazards include avoiding eye injury, respiratory protection, ventilation of the work area, protective clothing and having safe equipment to use.
Eye hazards include exposure to ultraviolet and infrared light. Welders and their helpers should wear filter glasses with shades ranging from 2 to 14, depending on the type of welding being done, to protect their eyes. Unless a welding arc is behind a screen, not only the welder, but also people nearby may need eye protection. Other workers should be excluded within a 30 foot radius from gas or low powered arc welding, or also be protected with appropriate filter lenses. Heavy welding requires a 100 foot radius. Inert gas welding produces 5 to 30 times as much ultraviolet light as arc welding and requires shielding for even greater distances. Keep in mind that ordinary untreated plastic lenses absorb ultraviolet light very poorly and should not be relied on for protection.
Virtually all welding processes generate gases, fume and dusts. Gases generated include carbon monoxide, carbon dioxide, ozone, and nitrous gases. Other gases may also be formed in the presence of chemicals which may be on the material being welded. For example 1,1,1 Trichloroethane generates phosgene gas when exposed to the heat of welding. Welding and cutting can also generate fumes from cadmium, lead, cyanide, beryllium, arsenic, fluorides, nickel, cyanide, and other materials when can be hazardous if inhaled. Proper respiratory protection should always be worn when cutting or welding. The best type of protection to use can be determined by reading the Material Safety Data Sheet for the material being welded, or the manufacturer of the rod or flux being used.
Mechanical ventilation at the rate of 2,000 cubic feet per minute per welder is required if the area is more crowded than 10,000 cubic feet per welder; has a ceiling height of less than 16 feet; or in confined spaces where structural barriers significantly obstruct cross ventilation. Additional specific ventilation requirements are necessary for fluorine compounds, zinc, lead, beryllium, cadmium, mercury, and for stainless steel that is oxygen cut using either a chemical flux or iron powder or gas shielded arc cutting. Where it is not possible to provide this ventilation, airline respirators, hose masks, or self contained units must be used. Oxygen should never be used for ventilation.
All parts of the body should be protected from radiant energy, sparks, and molten metal splashes. Clothing made from wool, or wool blends, is generally better than cotton. Some cutting operations such as inert-gas metal arc welding will cause exposed cotton clothing to rapidly deteriorate. Leather capes, jackets, leggings, and aprons provide additional protection especially in vertical, or overhead operations. Use of dark clothing will help reduce reflected light.
All welding equipment should be inspected each day prior to use. Report any defects found in regulators, torches or electrical components to a person that is qualified to make the necessary repairs.
Eye hazards include exposure to ultraviolet and infrared light. Welders and their helpers should wear filter glasses with shades ranging from 2 to 14, depending on the type of welding being done, to protect their eyes. Unless a welding arc is behind a screen, not only the welder, but also people nearby may need eye protection. Other workers should be excluded within a 30 foot radius from gas or low powered arc welding, or also be protected with appropriate filter lenses. Heavy welding requires a 100 foot radius. Inert gas welding produces 5 to 30 times as much ultraviolet light as arc welding and requires shielding for even greater distances. Keep in mind that ordinary untreated plastic lenses absorb ultraviolet light very poorly and should not be relied on for protection.
Virtually all welding processes generate gases, fume and dusts. Gases generated include carbon monoxide, carbon dioxide, ozone, and nitrous gases. Other gases may also be formed in the presence of chemicals which may be on the material being welded. For example 1,1,1 Trichloroethane generates phosgene gas when exposed to the heat of welding. Welding and cutting can also generate fumes from cadmium, lead, cyanide, beryllium, arsenic, fluorides, nickel, cyanide, and other materials when can be hazardous if inhaled. Proper respiratory protection should always be worn when cutting or welding. The best type of protection to use can be determined by reading the Material Safety Data Sheet for the material being welded, or the manufacturer of the rod or flux being used.
Mechanical ventilation at the rate of 2,000 cubic feet per minute per welder is required if the area is more crowded than 10,000 cubic feet per welder; has a ceiling height of less than 16 feet; or in confined spaces where structural barriers significantly obstruct cross ventilation. Additional specific ventilation requirements are necessary for fluorine compounds, zinc, lead, beryllium, cadmium, mercury, and for stainless steel that is oxygen cut using either a chemical flux or iron powder or gas shielded arc cutting. Where it is not possible to provide this ventilation, airline respirators, hose masks, or self contained units must be used. Oxygen should never be used for ventilation.
All parts of the body should be protected from radiant energy, sparks, and molten metal splashes. Clothing made from wool, or wool blends, is generally better than cotton. Some cutting operations such as inert-gas metal arc welding will cause exposed cotton clothing to rapidly deteriorate. Leather capes, jackets, leggings, and aprons provide additional protection especially in vertical, or overhead operations. Use of dark clothing will help reduce reflected light.
All welding equipment should be inspected each day prior to use. Report any defects found in regulators, torches or electrical components to a person that is qualified to make the necessary repairs.
Just some rambling
I've been working in shipbuilding industry for 6 month now. From what i see, most of the activities involves cutting and welding of metal. So i think this occurs is every workplace as well. Most of us don't really know what are the hazards and dangers associated with welding and cutting activities.
So i would like to dedicate this day as "Welding and Cutting Awareness Day". I'll post up a couple articles on welding and cutting and i hope it'll help.
Work Safe Everyone!
So i would like to dedicate this day as "Welding and Cutting Awareness Day". I'll post up a couple articles on welding and cutting and i hope it'll help.
Work Safe Everyone!
Thursday, September 13, 2007
EYE PROTECTION: PRESERVE YOUR VISION
As you leave the workplace today, look up, down and all around, observing the beauty around you. See the blue sky, the many shades of leaves in the trees, and the different birds that occupy them. When you get home, watch your children playing in the yard and pay attention to how their eyes light up when Daddy or Mommy gets home. Have you ever stopped to think how wonderful your eyesight really is? Well, think about it. For about two minutes, close your eyes completely and contemplate how life would be if you lost your eyesight! Did you come up with visions about how your life would change if you couldn't see? Did they include any of the following?
· When you and your family are on vacation, they will have to describe the scenery to you.
· You would have to be led wherever you want to go.
· Your spouse would have to describe the way your children's eyes light up when they open their presents at Christmas.
· No more leisurely activities such as hunting or fishing, watching movies or TV.
· No more driving the new truck you just bought.
Does this sound like something you want to go through? I didn't think so! Is there a way to prevent this from happening? You bet-wear your eye protection! A recent article in Safety & Health states that every day approximately 1,000 eye injuries occur in the U.S. OSHA estimates that 90% of eye injuries are preventable through the proper use of safety eye wear. What does this tell us? Many people are not wearing proper eye protection! Let's examine a few operations that present eye hazards:
· Grinding, hammering, chiseling, wood working or any other activity that might cause large fragments or small particles to fly through the air and into the eyes;
· Painting, spraying, sanding, metal working, spot welding or any process that may cause dust, fumes or tiny particulate to become airborne;
· Work tasks such as electric welding and cutting with a torch, furnace tending or operations around radiant energy or intense heat;
· Operations such as handling acids and caustics, and hot metal casting and babbitting where gases, vapors, liquids or splashing metals are generated.
Your eyesight is a precious gift. Please do not wait until it's too late to come to your senses. If your work presents an exposure to eye hazards, wear your eye protection.
Don't take chances. Open your eyes and protect your vision!
· When you and your family are on vacation, they will have to describe the scenery to you.
· You would have to be led wherever you want to go.
· Your spouse would have to describe the way your children's eyes light up when they open their presents at Christmas.
· No more leisurely activities such as hunting or fishing, watching movies or TV.
· No more driving the new truck you just bought.
Does this sound like something you want to go through? I didn't think so! Is there a way to prevent this from happening? You bet-wear your eye protection! A recent article in Safety & Health states that every day approximately 1,000 eye injuries occur in the U.S. OSHA estimates that 90% of eye injuries are preventable through the proper use of safety eye wear. What does this tell us? Many people are not wearing proper eye protection! Let's examine a few operations that present eye hazards:
· Grinding, hammering, chiseling, wood working or any other activity that might cause large fragments or small particles to fly through the air and into the eyes;
· Painting, spraying, sanding, metal working, spot welding or any process that may cause dust, fumes or tiny particulate to become airborne;
· Work tasks such as electric welding and cutting with a torch, furnace tending or operations around radiant energy or intense heat;
· Operations such as handling acids and caustics, and hot metal casting and babbitting where gases, vapors, liquids or splashing metals are generated.
Your eyesight is a precious gift. Please do not wait until it's too late to come to your senses. If your work presents an exposure to eye hazards, wear your eye protection.
Don't take chances. Open your eyes and protect your vision!
Monday, September 10, 2007
DON'T NEGLECT CUTS
Infection is often called 'Blood Poisoning'. It might be of interest to know exactly what is meant by 'Blood Poisoning'. The term itself indicates that it is a poisoning directly related to blood.
There are two ways in which a poison can attack our bodies. It may be taken in through the mouth and enter the body by way of the digestive organs, or it may enter directly into the blood stream through an abrasion or cut in the skin. In any event, every poison eventually works through the blood and the poison of infections works into the blood stream directly.
The smallest cut, abrasion or scratch is large enough for germs to enter. If they are not wash off they will cause an infection which could lead to blood poisoning. If left untreated, a hand or arm could become so infected that it might possibly have to be amputated.
Should you find yourself with a small scratch or cut be sure to get it washed out and properly covered with a clean bandage. 'An ounce of prevention is worth a pound of cure'. Serious cuts and lacerations need to be treated by professional medical personnel.
Most often you'll run up against smaller injuries - burns, nicks, scratches and cuts. The danger here is that most workers don't bother to get first aid for these minor injuries. The bottom line is - DON'T NEGLECT CUTS. Do your part by trying to prevent them from happening in the first place, but when any injury occurs - serious or minor - be sure that it receives the right kind of treatment, as quickly as possible.
First aid kits must be checked, frequently to be sure they are clean and fully stocked. This applies to your home and car or boat as well as on the job.
KEEP MINOR INJURIES MINOR! FIRST AID TREATMENT IS IMPORTANT TO PREVENT INFECTION.
There are two ways in which a poison can attack our bodies. It may be taken in through the mouth and enter the body by way of the digestive organs, or it may enter directly into the blood stream through an abrasion or cut in the skin. In any event, every poison eventually works through the blood and the poison of infections works into the blood stream directly.
The smallest cut, abrasion or scratch is large enough for germs to enter. If they are not wash off they will cause an infection which could lead to blood poisoning. If left untreated, a hand or arm could become so infected that it might possibly have to be amputated.
Should you find yourself with a small scratch or cut be sure to get it washed out and properly covered with a clean bandage. 'An ounce of prevention is worth a pound of cure'. Serious cuts and lacerations need to be treated by professional medical personnel.
Most often you'll run up against smaller injuries - burns, nicks, scratches and cuts. The danger here is that most workers don't bother to get first aid for these minor injuries. The bottom line is - DON'T NEGLECT CUTS. Do your part by trying to prevent them from happening in the first place, but when any injury occurs - serious or minor - be sure that it receives the right kind of treatment, as quickly as possible.
First aid kits must be checked, frequently to be sure they are clean and fully stocked. This applies to your home and car or boat as well as on the job.
KEEP MINOR INJURIES MINOR! FIRST AID TREATMENT IS IMPORTANT TO PREVENT INFECTION.
Subscribe to:
Posts (Atom)